Blackadder's Lucius Pattern Reaver

[Blackadder]

Reaver Asymmetry:


The asymmetry of this model is mind boggling, I suppose it's all right for the compounded curves of the Mars pattern but the Lucius requires square and true edges and panels for its faceted armour. The hull varies 1.0 to 2.0 MM between sides.


http://i.imgur.com/sD58Dil.jp

The inner surface of the carapace will have to be trued before the outer surface is applied.


Again where there are gaps between the hull carapace and the shoulder armour on the Mars the Lucius will have continuity in that the hull and shoulders will be joined and most probably a single unit. Not a problem but an interesting exercise.


Fortunately the shoulder mounts display very little Mars filigree so I should be able to get away with out replicating them in styrene. As with the Warhound the basic shoulder and legs are the same on both the Mars and Lucius.


http://i.imgur.com/U7tTbOf.jpg

It may be worthy of note the liberal use of rubber bands to hold the components together during this construction and fitting stage. Apart from the styrene work nothing is glued and all the parts are fitted to a fraction of an millimeter gap/clearance tolerance. It is worth the small added effort and time to achieve a professional looking assembly. The big failing I find with assembled (derelict) Baneblades I purchase on Ebay are the huge gaps between components usually filled with putty or glue.

 

[Blackadder]

Finally a Neck Armour I Can Live With:


After much trial and error I have come up with a hood design that seems workable.


Naturally the side angles need to be pared down but the overall concept mimics the Mars shape but also the Lucius motif. What is seen here is the underside skin of the shield; the exterior surface will give thickness to the armour.


Something as simple as this design should have been obvious to me but I was working under the constraints that the armour must not appear too bulky. Also since I am eliminating the hidden neck armour (The Hull Carapace will be removable in one piece) I had to allow for the hidden neck armour side flanges. This will become more apparent once the entire interior level of the hull carapace is completed.


http://i.imgur.com/yVKlSi6.jpg

In this top view note the original measurements and the fillet pieces necessary to amend the hood to its final configuration.


http://i.imgur.com/HQDwBLl.jpg

Finally, a shot of the sub-structure that will flesh out the original contours to mount the sub hood assembly components I shall be retaining.


http://i.imgur.com/12izksk.jpg

I still haven't worked out these details.

 

[Blackadder]

The Hull Carapace Ad Nauseam:


Once more into the breach dear friends, working the Mars carapace into a viable Lucius pattern without making it look too much like an L. Pattern Warhound takes a bit of doing.


http://i.imgur.com/4bxhBgE.jpg

http://i.imgur.com/OCWK7hm.jpg

I've decided to try some vents on either side of the centerline, that might be fun. I need something to break the line so it doesn't ape the Mars carapace too closely but isn't the truncated box on the Warhound's back.


http://i.imgur.com/0XUKzhJ.jpg

Anyway I seem to have a lot of space left above the hull compartment and the Void generators won't conflict with anything I have built thus far.


http://i.imgur.com/xhzkDud.jpg

 

[Slybarbeau]

I never stop to be amazed at what you are doing. I am fallowing religiously each you your tread with lot of interest. That's it giving me a lots of idea to modify (on a much smaller scale) some of my space marine tanks .....and orks....
Thanks you sir

 

[Blackadder]

Thanks, I have to admit this project is a lark, I have no idea if it can be accomplished (in the manner I envision the result that is.........) but it pleases me to hear that my efforts inspire others to scratch building as (To me) there is not much more satisfying that building something from basic materials.

 

[Blackadder]

Reaver Carapace and Hood Extension

So the Reaver has a hood the fairs into the main hull carapace and for some reason has a second hood beneath that hood.


Well initially I thought to eliminate the lower hood but I found I cannot as it projects rearward beyond the main hood which seemed irreconcilable until I hit on a solution unfortunately at 02:30 AM. awakening with that epiphany I lost sleep for a good portion of the rest of the night.


I shall build an partial under-hood and secure the exterior hood to the under-hood and thereby eliminating the excessive construction that would bulk up the carapace too much, simple Huh! Well it took two days for me to come up with the solution.

http://i.imgur.com/K4uUXVw.jpg

Shown here is the under-hood with the side flanges in place and cut at what I hope will be the angles and sizes but I won't know that until I build the exterior hood and carapace.


http://i.imgur.com/OR84Ubk.jpg

The only plus on this construction is that it doesn't follow the Reaver model from Dawn of War pattern but still maintains the Reaver configuration.


http://i.imgur.com/HSx4HSo.jpg

The inner hood extends 45 MM from the front hull and the external will extend 60 MM the same as the Mars design.


http://i.imgur.com/LZDrV7y.jpg

So far it's working.

 

[wargamesculptor]

really great approach to this model and so far the best version of a lucius pattern reaver that i've seen in any scale!

 

[Blackadder]

Whoa, best version, that'll take some living up to. I hope I'm worthy of such confidence.

Thanks,


Void Generator Housings:


Here is where we get into the nitty-gritty of this project.


I have to duplicate the Void Generator housings instead of just covering them with styrene else-wise they will be too bulky looking.
http://i.imgur.com/X7icEXH.jpg

Fortunately there is an inner flange that locks the generators into place in the model so duplicating the area that locks behind the flange Part 1R will also lock the L. Pattern constructs as well.


http://i.imgur.com/MXCP51k.jpg

I am going to make the rear floor under the generators one continuous piece instead of two separate generator housings to take advantage of the locking effect as well.


http://i.imgur.com/J7yoa7N.jpg

Once the Lucius Generators are assembled I plan to fill them with putty or some other weighty material as the Gen's. also serve as counterweights on the original model.

 

[Blackadder]

The Void Generator Housings 2


Its a real pleasure to work on this model, all the angles are crisp and true; now of the warping so prevalent on older FW castings.


Below we have the base of the void generators, a continuous floor plate instead of two separate housings


http://i.imgur.com/POrG4xq.jpg

The two interior pillars that lock the generator housings into the hull strangely distorted appearing in this image but they are not.


http://i.imgur.com/JVjX8mk.jpg

The interior view of the pillars in place showing the close tolerance fit.


http://i.imgur.com/guXxApF.jpg

The exterior with foot plates and mounting stringers in place ready to receive the housing inner walls.


http://i.imgur.com/oqEm2vD.jpg

 

[Blackadder]

Void Generator Housings part 3


Yeah I know lots of pictures of virtually the same thing but anyone interested in copying this construction will probably appreciate the step by step process.

The rest of you will just have to bear with the redundancy.


I made a tracing of the inboard generator housing profile and squared off the corners. Due to the flexibility of the construction I took a guess and a gamble at the placement of the two dimensional pieces as it was impossible to glue, align and clamp at the same time. Actually having a helper at this time would be well er helpful.


Fortunately the alignment of the pieces were spot on so no need to cut the glue joint and redo.


Note in the profile image below the generators are parallel with the forward carapace but about a millimeter or two lower. This is as it should be to allow for the surface sheet styrene pieces which will be applied after the counterbalance filler material is installed.


http://i.imgur.com/mB3tHwT.jpg

Here we see in this quarter view the slight step down of the housings compared to the main carapace; this is intentional.


Note also that the housing profile pieces appear to converge toward the front, that is because the center section is still not installed. I've decided to make a Lucius center piece and glue it in place rather than use the one that came with the kit for both versions.


http://i.imgur.com/xFB7zG0.jpg

In this above shot you can see the construction is pretty much symmetrical even though at this stage the components are relatively flimsy.


http://i.imgur.com/bn2B3OK.jpg

Heres a view of the bottom that I neglected to show in the previous post showing the aligning channels that keep the Generators centered on the model.


http://i.imgur.com/6pn1koL.jpg

 

[Blackadder]

Ventilator Unit:

Between the Void Generators there is the Ventilator Unit. Since I want the generator assembly in one piece I need to make a second set of vent housings.


The build is pretty straightforward with a bit of Lucius angles to keep things interesting.

http://i.imgur.com/3dcwZRI.jpg

http://i.imgur.com/jMKE9PZ.jpg

 

[Blackadder]

Ventilator Unit 2



The major hull components assembled without gluing showing the well thought out FW engineering. Ya gotta give these guys credit.


http://i.imgur.com/6GuNLUw.jpg

Note the wire wrapped tubing in the foreground. That will be changed to styrene rods.


http://i.imgur.com/pfhRR7m.jpg

 

[Blackadder]

Central Ventilator Continues:


This is not a very popular thread judging by the number of hits it has received. This goes along with my personal opinion of the Reaver Titan in general; that it is not that popular of a model and that were FW to have produced a Warlord instead it would have been better received.


In spite of this I shall persevere in this endeavor to the bitter end.


Work continues on the Central Ventilator console with the securing the spiral conduit to the base construction. Unfortunately I have exhausted my local hobby stores of material; "Jeez Blackadder what are you doing with all that plasticard?" is the usual query. To which I say, "You don't check your incoming emails do You?"


http://i.imgur.com/NWfJR1j.jpg

Not much to say about the images posted all should be self-explanatory Although I welcome any questions.


http://i.imgur.com/bjlwrGx

http://i.imgur.com/BqC3eqc.jpg

http://i.imgur.com/jTgzqoO.jpg

 

[wargamesculptor]

I always wanted to see a Lucius reaver but was disappointed with the FW epic version, really like your version and very likely build my own epic version based off your design. Keep up the stellar work sir !

 

[Blackadder]

Thanks,

How big is an Epic Reaver?

 

[wargamesculptor]

There approximatley 55mm tall

 

[Blackadder]

Gamera Lookalike:

I finally realized why my animus toward the Reaver model well one of the reasons.


Anyway my instincts regarding the head were correct the Mars head won't work with the Lucius Design.


http://i.imgur.com/3Mi8Ixo.jpg

Top view not much better.


http://i.imgur.com/m0KUTLG.jpg

Too much like a certain turtle with a flatus problem.


http://i.imgur.com/JUzx2CA.jpg

 

[wargamesculptor]

As the cowling is separate is it possible to make a Lucius pattern cowling more streamlined ? (not trying to make more work for you sir ) maybe slightly shorter as the cowling seems to come quite far forward ?

 

[Blackadder]

The Integral Generators:

The generators are ostensibly one plug in unit now and all that is left is to apply the skin to the housings. Then the detail goes on.


http://i.imgur.com/dPfvcj6.jpg

The clothespins won't be necessary once the generators are weighted.


http://i.imgur.com/eZefzJN.jpg

The inner lining is just about ready for the interior detail.


http://i.imgur.com/Jv92cWi.jpg

There is room for about a pound of weight in each housing.


http://i.imgur.com/07Caocg.jpg

 

[wargamesculptor]

wow your building two at the same time!